L293D Quadruple Half-H Driver

20.00 EGP

The L293D is a popular 16-Pin Motor Driver IC. As the name suggests it is mainly used to drive motors. A single L293D IC is capable of running two DC motors at the same time; also the direction of these two motors can be controlled independently.

Out of stock

L293D Pin Configuration

Motor Driver IC L293D Pinout

Pin Number Pin Name Description
1 Enable 1,2 This pin enables the input pin Input 1(2) and Input 2(7)
2 Input 1 Directly controls the Output 1 pin. Controlled by digital circuits
3 Output 1 Connected to one end of  Motor 1
4 Ground Ground pins are connected to ground of circuit (0V)
5 Ground Ground pins are connected to ground of circuit (0V)
6 Output 2 Connected to another end of  Motor 1
7 Input 2 Directly controls the Output 2 pin. Controlled by digital circuits
8 Vcc2 (Vs) Connected to Voltage pin for running motors (4.5V to 36V)
9 Enable 3,4 This pin enables the input pin Input 3(10) and Input 4(15)
10 Input 3 Directly controls the Output 3 pin. Controlled by digital circuits
11 Output 3 Connected to one end of Motor 2
12 Ground Ground pins are connected to ground of circuit (0V)
13 Ground Ground pins are connected to ground of circuit (0V)
14 Output 4 Connected to another end of Motor 2
15 Input 4 Directly controls the Output 4 pin. Controlled by digital circuits
16 Vcc2 (Vss) Connected to +5V to enable IC function

 

Features

  • Can be used to run Two DC motors with the same IC.
  • Speed and Direction control is possible
  • Motor voltage Vcc2 (Vs): 4.5V to 36V
  • Maximum Peak motor current: 1.2A
  • Maximum Continuous Motor Current: 600mA
  • Supply Voltage to Vcc1(vss): 4.5V to 7V
  • Transition time: 300ns (at 5Vand 24V)
  • Automatic Thermal shutdown is available
  • Available in 16-pin DIP, TSSOP, SOIC packages

Note: Complete Technical Details can be found in the L293D datasheet given at the end of this page.

L293D Equivalent Dual Timer IC

LB1909MC, SN754410, ULN2003

 

Where to use L293D IC

The L293D is a popular 16-Pin Motor Driver IC. As the name suggests it is mainly used to drive motors. A single L293D IC is capable of running two DC motors at the same time; also the direction of these two motors can be controlled independently. So if you have motors that have operating voltage less than 36V and operating current less than 600mA, which are to be controlled by digital circuits like Op-Amp, 555 timers, digital gates or even Micron rollers like Arduino, PIC, ARM etc.. this IC will be the right choice for you.

How to use a L293D Motor Driver IC

Using this L293D motor driver IC is very simple. The IC works on the principle of Half H-Bridge, let us not go too deep into what H-Bridge means, but for now just know that H bridge is a set up which is used to run motors both in clock wise and anti clockwise direction. As said earlier this IC is capable of running two motors at the any direction at the same time, the circuit to achieve the same is shown below.

L293D Circuit

All the Ground pins should be grounded. There are two power pins for this IC, one is the Vss(Vcc1) which provides the voltage for the IC to work, this must be connected to +5V. The other is Vs(Vcc2) which provides voltage for the motors to run, based on the specification of your motor you can connect this pin to anywhere between 4.5V to 36V, here I have connected to +12V.

The Enable pins (Enable 1,2 and Enable  3,4)  are used to Enable Input pins for Motor 1 and Motor 2 respectively. Since in most cases we will be using both the motors both the pins are held high by default by connecting to +5V supply. The input pins Input 1,2 are used to control motor 1 and Input pins 3,4 are used to control Motor 2. The input pins are connected to any Digital circuit or microcontroller to control the speed and direction of the motor. You can toggle the input pins based on the following table to control your motor.

Input 1 = HIGH(5v) Output 1 = HIGH Motor 1 rotates in Clock wise Direction
Input 2 = LOW(0v) Output 2 = LOW
Input 3 = HIGH(5v) Output 1 = HIGH Motor 2 rotates in Clock wise Direction
Input 4 = LOW(0v) Output 2 = LOW

 

Input 1 = LOW(0v) Output 1 = LOW Motor 1 rotates in Anti-Clock wise Direction
Input 2 = HIGH(5v) Output 2 = HIGH
Input 3 = LOW(0v) Output 1 = LOW Motor 2 rotates in Anti -Clock wise Direction
Input 4 = HIGH(5v) Output 2 = HIGH

 

Input 1 = HIGH(5v) Output 1 = HIGH Motor 1 stays still
Input 2 = HIGH(5v) Output 2 = HIGH
Input 3 = HIGH(5v) Output 1 = LOW Motor 2 stays still
Input 4 = HIGH(5v) Output 2 = HIGH

 

Applications

  • Used to drive high current Motors using Digital Circuits
  • Can be used to drive Stepper motors
  • High current LED’s can be driven
  • Relay Driver module (Latching Relay is possible)

 

2D Model of L293D (PDIP)

L293D Dimesions

L293D IC Dimensions

Need Help?

Please get in touch with us through our Contact Us page.

Reviews

There are no reviews yet.

Be the first to review “L293D Quadruple Half-H Driver”

Category: Tags: , ,